Welcome to the official website of Shandong Mingding supply Chain Management Service CO.,LTD
Cr12 Hot Rolled Steel Round Bars
Product Category：
Email:
WhatsApp:
Cr12 Hot Rolled Steel Round Bars
Applications of Cr12 steel material
Cr12 steel is a typical alloy Tool steel, Cr12 is a chinese Cold Work Alloy Tool Steel. Its Cold work Mechanical Properties is very nice. Cr12 steel with high abrasion resistance, micro deformation of cold work die steel, the wind hard tool steel, carbon content as high as 1.5%, chromium content as high as 11.5%, the heat treatment hardness can reach 60 HRC. Cr12 section steel can be used to：
a) silicon die is mainly used for small dynamic loaGBg conditions require high wear resistance, simple shape drawing and blanking dies.
b The system for manufacture benGBg molds requiring high wear, the complex shape of the punch, die, inserts, do punch, when the die is recommended, hardness 60 ~ 64HCR.
c) for the manufacture of drawing die die wear required, it is recommended hardness 62 ~ 64HCR.
d) for anti-cold aluminum extrusion die punch, it is recommended hardness 60 ~ 62HCR.
e) for benGBg carbon content of 0.65% to 0.80% proof builGBg steel, hardness 60 ~ 62HCR.
f) can be used for blanking die, punch, rolling wheels, shear blades, cold heaGBg die, clay mold.
g) can be used for thermoset plastic molGBg molds.
Chemical and Mechanical
Chemical composition(wt.%) of Cr12 grade: GB/T 1229-2000
| Elements | Min.（≥） | Max.（≤） |
|---|---|---|
| C | 2.00 | 2.30 |
| Si | - | 0.40 |
| Mn | - | 0.40 |
| Cr | 11.50 | 13.00 |
Mechanical properties of grade Cr12 GB/T 1229-2000
| Proof strength Rp0.2 (MPa) |
Tensile strength Rm (MPa) |
Impact energy KV (J) |
Elongation at fracture A (%) |
Reduction in cross section on fracture Z (%) |
As-Heat-Treated Condition | Brinell hardness (HBW) |
|---|---|---|---|---|---|---|
| 539 (≥) | 215 (≥) | 42 | 14 | 42 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 244 |
GB Cr12 alloy tool steel material equivalent -UNS T30403
| Grade | C | Si | Mn | P | S | Cr | Mo | V |
| D3 | 2.00～2.35 | 0.10～0.60 | 0.20～0.60 | 0.030 MAX | 0.030 MAX | 11.0～13.5 | ~ | 1.00 MAX |
| SKD1 | 1.90～2.20 | 0.10～0.60 | 0.20～0.60 | 0.030 MAX | 0.030 MAX | 11.0～13.0 | ~ | 0.30 MAX |
| Cr12 | 2.00～2.30 | 0.40 MAX | 0.40 MAX | 0.030 MAX | 0.030 MAX | 11.50～13.00 | ~ | ~ |
| 1.2080/ X210Cr12 | 1.90～2.20 | 0.10～0.40 | 0.15～0.45 | 0.030 MAX | 0.030 MAX | 11.00～12.00 | ~ | ~ |
Applications of Cr12 steel material
Cr12 steel is a typical alloy Tool steel, Cr12 is a chinese Cold Work Alloy Tool Steel. Its Cold work Mechanical Properties is very nice. Cr12 steel with high abrasion resistance, micro deformation of cold work die steel, the wind hard tool steel, carbon content as high as 1.5%, chromium content as high as 11.5%, the heat treatment hardness can reach 60 HRC. Cr12 section steel can be used to：
a) silicon die is mainly used for small dynamic loaGBg conditions require high wear resistance, simple shape drawing and blanking dies.
b The system for manufacture benGBg molds requiring high wear, the complex shape of the punch, die, inserts, do punch, when the die is recommended, hardness 60 ~ 64HCR.
c) for the manufacture of drawing die die wear required, it is recommended hardness 62 ~ 64HCR.
d) for anti-cold aluminum extrusion die punch, it is recommended hardness 60 ~ 62HCR.
e) for benGBg carbon content of 0.65% to 0.80% proof builGBg steel, hardness 60 ~ 62HCR.
f) can be used for blanking die, punch, rolling wheels, shear blades, cold heaGBg die, clay mold.
g) can be used for thermoset plastic molGBg molds.
Forging of Cr12 steel material
Preheat slowly to 900~950°C then increase the temperature more rapidly to 1050-1100 °C. Do not forge below 1020°C. Then cool the Cr12 slowly after forging.
Annealing of Cr12 steel material
GB Cr12 tool steel is delivered condition normal at annealing and machineable. If need re-annealing. Heat to the Cr12 steel 900 °C and Soak thoroughly, then cool in furnace. After annealing, the Cr12 delivery hardness is 255HB Max.
Stress Relieving of Cr12 steel material
When must tools made from Cr12 alloy tool steel are heavily machined or ground , the relief of internal strains is advisable before hardening to minimise the possibility of distortion. Stress relieving is very necessary, stress relieving should be done after rough machining. To stress relieve, heat the component carefully to 600-650°C, allow a good soaking period (two hours per 25mm of ruling section). Cool in the furnace or in air. The tools be finish machined before hardening.
Hardening of Cr12 steel material
GB Cr12 Delivery condition usually is Annealing, so hardening is necessary. Heat the Cr12 tools in a controlled atmosphere furnace, if have not the controlled furnace, pack hardening is recommended strongly. Pre-heat Cr12 tool steel to 750~800°C, soak enough time until heat through. Then brought up to 1000-1040 °C, cooling in air or oil quenching.
Tempering of Cr12 steel material
Heat the GB Cr12, Heat uniformly to the required temperature allowing a soaking time of two hours per 25mm of ruling section. Withdraw from the furnace and allow to cool in air. Different tempering temperature will get different hardness. Typical tempering is 204°C, after tempering hardness 61HRc Min.
Welding of Cr12 steel material
In general, we do not advise the welGBg of alloy tool steel but users sometimes prefer to weld in order to avoid the cost of retooling. It should be remembered that this grade is an air hardening steel and that in welGBg the area of the weld attains a temperature of about 1000°C. Cracking is likely to occur during cooling unless proper precautions are taken. Popular methods of welGBg are atomic hydrogen and argon arc. We recommend you contact your welGBg consumables supplier who should provide you full assistance and information on welGBg alloy tool steels.
Nitriding of Cr12 steel material
Cr12 alloy tool steel can be nitrided to give a hard surface case. After the nitriGBg heat treatment, the Cr12 is then very resistant to wear and erosion. NitriGBg also increases resistance to corrosion.
Final Grinding of Cr12 steel material
GrinGBg the GB Cr12 Steel. Select the correct grade of wheel in consultation with the grinGBg wheel manufacturer. Ensure the grinGBg wheel is in good condition by means of a suitable dressing tool. Wet grinGBg is a preferable option using a copious supply of coolant. If dry grinGBg is resorted to then use a very soft wheel.
Factory video
Shandong Mingding Supply Chain Management Service Co., Ltd. was established in 2013, focusing on the production, processing and trade of metal materials. We have a professional team to provide quality service, we sincerely welcome customers at home and abroad to visit our company for guidance and long-term cooperation.
Warehouse storage
The company has the most advanced production equipment and automatic control system, to ensure the most reliable product quality. In addition, we also have a professional international trade and logistics team. With quality products and excellent service, we have established a large number of long-term customers all over the world.
Packing and delivery
To better ensure the safety of your goods, professional, environmentally friendly, convenient and efficient packaging services will be provided.
Production Technology
Our main products include high quality carbon steel, stainless steel products,galvanized steel products, aluminum and copper. We can also provide cutting, punching, bending, polishing, shearing, wire drawing and other related service.
Honor
Application
Our company is set production processing and trade as one. The company has the most advanced production equipment and automatic control system, to ensure reliable product quality and sufficient supply capacity. Our main products are stainless steel, silicon steel, galvanized steel, carbon steel, aluminum products and other series. Applicable to engineering, coal mining, shipping, aviation, boiler, machinery, military and other fields. We sincerely welcome customers from all over the world to visit our company to discuss long-term cooperation.
Architectural field
Architectural field
Automotive field
Automotive field
Aviation field
Aviation field
Chemical industry field
Chemical industry field
FAQ
How do you package the product?
The inner layer is covered with waterproof paper, packed in iron and secured by fumigated wooden brackets. It can effectively protect products from corrosion in the process of sea sample transportation.
Are the products inspected before shipment?
Of course. All our products go through strict quality tests before they are packed. Those that fail will be destroyed.
Can I visit your factory?
Of course. We welcome customers from all over the world to visit our factory.
What certifications have your products passed?
We have ISO 9001, SGS, EWC and other certifications.
Can you provide samples?
Of course, we can send samples all over the world. Our samples are free of charge, but the customer needs to bear the Courier charge
What is the loading port?
Normally, we ship from Shanghai, Tianjin, Qingdao and Ningbo ports. You can choose other ports according to your needs.
Related Products
Message
Add：Shan Gang Building, 61-11 South Gongye Road, Jinan Area, China (Shandong) Pilot Free Trade Zone
MD Steel
Message
info@mingdingsteel.com
+8615553113555